Price of liquid silicone rubber for gypsum sculptures mold making

FOB Reference Price:Get Latest Price
$6.00 - $6.50 / Kilogram | 200 Kilogram/Kilograms (Min. Order)
Report Suspicious Activity
Quick Details
Place of Origin:
Guangdong, China
Brand Name:
Rongxingda Silicone
Model Number:
Product name:
silicone rubber for mold buy
100% raw material
25±2 shore A
Mixing ratio:
for mold making
high dumplication time
Shelf life:
12 months
Supply Ability
Supply Ability:
20000 Kilogram/Kilograms per Month silicone rubber for mold buy
Packaging & Delivery
Packaging Details
1kg/5kg/25/200kg package
Shenzhen, China

Price of liquid silicone rubber for gypsum sculptures mold making

Product Description


RXsilicone  RX-825

Pourable ,Condensation Cure Mold Making RTV2 Silicone Rubber

Condensation tin cure molding silicone rubber, Tin-based silicone, also called condensation-cure silicone, are two-component materials which cure at room temperature (RTV) to flexible, high tear-strength rubbers. Tin cured silicone can be poured onto models or they can be made brush-able by adding a Thixotropic additive. They are ideal for molds where easy release or high temperature resistance is required.


Condensation Cure Mold Making RTV2 Silicone Rubbers can be poured or brush onto products for casting polyurethane,epoxy, polyester resin, gypsum/plaster, cement, waxes, low melt alloys/metals, etc.


Middle Shore A hardness (approx. 25)

Excellent tear strength

 Little rate of deformation and shrinkage

 Very high elongation and flexibility

High temperature resist,high tear resist

       Physical properties of Condensation Cure Mold Making RTV2 Silicone Rubber


Curing Agent(Part B)  


Mixing Ratio By Weight

Pot life Time

De-mold Time

Full Curing




60-70 min

6 Hours

10 Hours



30-40 min

4 Hours

8 Hours



15-20 min

2 Hours

5 Hours


Antioxidant Agent

If mix 0.5%-1% ratio of RTV2 silicone Antioxidant agent into silicone rubber, it can great increase using times about 30%-100%, and casting resins resist, particularly polyesters.

Thixotropic agent

Thickening agent for silicone rubber for vertical surface application(making brush-on molds)        

Preparing the Model

Porous surfaces, such as wood, should be dried and sealed. Also applying a release agent, such as petroleum jelly will aid in easy release of a silicone mold. Because silicone can sometimes bond to surfaces which contain silica, such as glass, cements and natural stone; it is recommended to do a spot test for possible adhesion.


Product data                  

Typical general characteristics

Inspection Method


Product data(uncured)






Viscosity, dynamic at 23℃ , after stirring


20000±2000 mPa.s

Density at 23℃


1.08 g/cm³




Product data (catalyzed with 2-4 wt % Catalyst Tin-4)

Viscosity at 23℃

ISO 3219





Product data (cured)



Density at 23℃ in water

ISO 2781

1.08 g/cm³

Hardness Shore A

ISO 868


Tensile strength

ISO 37

>3.5 MPa

Elongation at break

ISO 37


Tear strength

ASTM D 624 T

>25 N/mm

Tear strength

ASTM D 624 B

>45 N/mm

Linear shrinkage




Mixing instrustions 

This material can readily accept pigments.Stirring individual components before use is recommended. Make sure to weigh and measure accurately. Close containers tightly after use. Products should be stored in their original, sealed containers in an environment that does not exceed 90. Under these conditions, the product will achieve the expected shelf life.


The following procedure is an example of a 100:3 mix ratio addition cure product. Please refer to the product’s technical sheet for mix ratio information:


Mixing: Charge 100kg by weight of “Part A” and 3kg by weight of “Part B” into a clean, compatible metal or plastic container. The volume of the container should be 3-4 times the volume of the material to be mixed. This allows for expansion of the siloxane material as it de-gasses.

Mix thoroughly by hand or with mixing equipment while minimizing air entrapment until a homogeneous mixture is obtained. This will occur when the material takes on a uniform color with no visible striations. Scrape the sides and bottom of the container thoroughly several times while mixing. Once mixing is complete it is recommended that the material be de-aired 2-3 times by intermittent evacuation for a few minutes to minimize any imperfections due to bubbles in the cured material. Typically after releasing the vacuum 2-3 times the mass will collapse on itself at which time the vacuum should be left on only 2-4 minutes longer.



The 'Best use before end' date of each batch is shown on the product label. Storage beyond the date specified on the label does not necessarily mean that the product is no longer usable. In this case however, the properties required for the intended use must be checked for quality assurance reasons.

Packing information

Silicone Base is available in 1kg/5kg/20kg/25kg/200kg plastic/iron drum.Curing Agent is available in 0.25kg,1kg,5kg and 25kg plastic/iron drum.Vacuum bag can be used according to users demand.                                


Avoid contact with mucous membranes and eyes. Best method of cleanup is by wiping with disposable paper towels and washing with waterless hand cleaner, then soap and water. If solvents must be used, denatured ethyl alcohol is best, but should be handled with respect for health and flammability hazards.

The information and recommendations in this publication are to the best of our knowledge reliable. However nothing herein is to be construed as a warranty or representation. Users should make their own tests to determine the applicability of such information or the suitability of any products for their own particular purposes. Statements concerning the use of the products described herein are not to be construed as recommending the infringement of any patent and no liability for infringement arising out of any such use is to be assumed.

Product Display


More Products

Company Information




Package & Shipping